Видео

Rubbish again! After 2,5 years in use displays wrong temperatur with nearly 40° celsius. I have no other device on board that has been replaced so often in 10 years. With the 810, I thought the problems had been solved. Unfortunately, I was disappointed again!

it was announced almost a year ago but it cant find anywhere

Please take off the music, its awful

Do you have a video showing how to replace paddlewheel on a DST800?

What is the weight of the transducer of 600W (P79) ?

Thank you Zack, very knowledgeable presentation. Please longer and more detailed next time!

what is the typical life span of the B60 transducer? mine failed after 2.5 years...

I have a 1999 Johnson ocean pro on a 1999 hull I have a Lowrance ti9-2 can this smart technology be used to start monitoring my engine and other equipment as was discussed in the video thanks great technology and from the same town I live in Milford

hello, what about installation on sailboats? where is the best zone for placing the transducer?

Why don't you guys ever talk about hooking up (wiring ) the transducer to the display box? and what transducers are compatible with different display panels?

Looks like it doesn’t have to be incredibly tight which is a relief for me. I ordered the flat wrench, but the slots on top of the transducer are so short it was hard to get any good torque without the wrench slipping off. I used just as much 4200 and had someone holding the transducer from underneath the boat to help me get some good turns on the nut. I probably managed to get it a little tighter than this video but I was still worried until I found this!

another fine presentation by Zack. You have for many years "connected the dots" I find these youTube presentations informative. Thanks!

Please, I would like to have more information about how to perform the calibration. I mean, is there any detailed step by step guide?

Nice job Zack but stacking up those Maretron Tee's is asking for trouble no matter how well they're tied up! The Actisense quad Tee's would be a much better solution...

Excellent presentation Zack! Cannot get over the depth of information & ease of touch screen in wheelhouse. Understand each Airmar module can also send data via bluetooth?

Hi Mike, I wanted to ask. I have the B175HW and it has been working great. It was set to 800hz . I have been seeing the fish marking really well. The waters I fish are from anywhere 12ft. to over 100. Do I customize my frequency based on depth for example 24 feet but then what would I change it to when drifting 70 to 30 feet etc? Just curious but I love this transducer. Also, if I find fish stacked up in an area on a drift, should I just drift it or set my minn kota to spot lock. just off the fish or on top of them? Thanks for your help.

FYI -- All the text (shirt logo, components and numbers) in the first 2:20 are left-right reversed in the video. It makes it harder for anyone to read it properly.

M 5

You're missing details for a Catamaran Powerboat. Where do you put one that's a through hull Transducer?

Can this be anti foul painted ?

I own a TM275LH... what’s the frequency to use when running at speed? I lose bottom at about 150ft running at 20kts

What if i have like a full keel running down the center of my hull? Not as deep as on sailboats but still. Will it cause any turbulence with a regular mount on a starboard side?

Looking to replace ST60+ sensors. I have two sizes of removable sensor housings, one is smaller for the paddlewheel sensor, the other is larger, for temp/depth. Is there any chance this sensor would fit these existing housings?

I am going. To guess this can't be done on Aluminum Hulls....?

Yikes... I like my spacers/washers to cover a thread or 2. If you look closely, the last washer is below the thread line. Definitely made up for it with the sealant.

What type of transducer would you recommend for a ferrocement hull, Great video, thanks

I used a cleaning transducer instead of fishing transducer

Very helpful. Thanks for posting.

Why not use your GPS, that will never foul... why do we care if we are doing 5 knots or 5.5 knots, have seen or heard about the unit coming apart, water rushing in....

Pero es muy impresionante protección

Hola no sé nada de tennogia

Thank you! Just what I needed to know! 🙏

Should use tape to cover the face of the transducer to avoid ANY sealant getting on it, and mitigate any needs to use cleaners on it. Also must ensure the arrow on the transducer points towards the keel, which is critical for proper orientation. If you use tape on the face of the 'ducer you can draw an arrow on it that matches the arrow on the top of the transducer. This way you can ensure proper orientation when installing it. I like how you removed the old transducer, but should specify the size of the hole saw needed.

What size was the hole saw?

Is there any detailed documentation online for the Smartflex alterting? The owners manual has no real detail on this.

I’m considering putting a long range livescope under my Allison 21 xb. . Any suggestions?

I just watched this video😳😁😁

Boring music. Terrible and unbearable to watch the video until the end.

Why isn't a doppler effect used in your modern sensors instead of using moving parts?

Me puede ayudar para poder hacer una instalación correcta

Hola tengo un transducer 525T-BSD como puedo instalarlo en un bote inflable tipo sodiak. Lo que tengo que indicar es que la Kia del bote también es inflable.

What type of glue do you use to bond a PZT sensor to PEEK material?

I have a tm185hw with a Simrad Go9 XSE and I am not able to mark depth or fish over 5 mph. I am in the process of doing some adjustments to see if I can improve on that. What settings would you use for palegic fishing and also for bottom fishing in 50-300 feet of water?

You said nothing about orientation of the transducer angle for the hull deadrise. Thats a critical detail to overlook isn't it. By the looks of the video its orientation isn't close pointing down. I hope I am wrong for their sake.

I've been waiting 2 years for the B275LHW install.

what is the sampling rate for this sensor?

Is there a music-free version of this video????

I'm getting a sea chaser 24HFC which has a stepped hull can you give me the model for a high frequency and an active 3-1 for the simrad thx

ya Airmar F your paddle wheel sensors